printhaser.blogg.se - Shift linkage bushing replacement

#SHIFT LINKAGE BUSHING REPLACEMENT HOW TO#
#SHIFT LINKAGE BUSHING REPLACEMENT PDF#
#SHIFT LINKAGE BUSHING REPLACEMENT INSTALL#
#SHIFT LINKAGE BUSHING REPLACEMENT DRIVER#
#SHIFT LINKAGE BUSHING REPLACEMENT DOWNLOAD#

This allows the engine to spin freely from the transmission. This fluid coupling uses a separate pump and a turbine spinning in opposite directions in the converter. Instead of using the clutch this type of transmission uses the torque converter.

#SHIFT LINKAGE BUSHING REPLACEMENT DRIVER#

Thus, the driver does not require to shift gears. It automatically changes the vehicle’s gear ratio as it moves.

Don't forget to reconnect the fan shroud if applicable.An Automatic Transmission is a type of motor transmission fitted in vehicles.

#SHIFT LINKAGE BUSHING REPLACEMENT INSTALL#

Install the rod and clip, raise engine and replace the plate and tighten bolts.

Install the new bushing using the grease to get it to install easily.

But for you 190E 2.6 owners it will still not be easy !!!.

Keep a little pressure on the bottom of the transmission pan with the jack.

Do not let the engine and transmission "hang" on their own.

Lower it down almost as far as it will do.

Go slowly since you will be lowering the engine as well.

Lower the transmission down as far as it will go using the jack.

Two bolts on each side of the plate that secure it to the subframe of the car.

Remove the steel cross plate for the rear transmission mount.

Raise the transmission to take the weight of rear rubber transmission mount.

Do not let the exhaust system just "hang" in the air - hard on manifolds and joints.

Remove the rubber exhaust hangars but keep it tied up loosely with a rope.

The rear of the exhaust system will also need to drop down as you lower the transmission.

If the fan has lots of clearance from the shroud, then you can skip the above step.

This will keep the fan from breaking the shroud when you tilt the engine.

Go into the engine compartment and loosen the plastic fan shroud at the back of the radiator.

You will need a jack and a large piece of plywood to place between jack and transmission pan.

So the engine and transmission drop down together.

You are just "lowering" the rear of the transmission with it still attached to the engine.

Remember you are not removing the transmission from the engine.

#SHIFT LINKAGE BUSHING REPLACEMENT HOW TO#

Here are some tips on how to get more working space: On some other models, you may need to consider this extra step. If you have room to get the tool up alongside the tunnel and can manipulate the tool then you will not need to lower the back of the transmission. On some 190E 2.3 or 190D diesels there may or may not be enough room.

This is particularly true with the 190E 2.6 models. The rear of the transmission will have to be dropped down in order to replace the bushing on the transmission shift arm. LIMITED WORKSPACE ALERT: You will have a real challenge on SOME models since there is so little room to work up alongside the transmission tunnel when replacing the forward bushing. Do NOT use too much grease as that will only result in more dirt and grime collecting on the bushing over time. That will help to increase the life of the new bushing. Then put a little grease on the rod ends when you reinstall it on the levers. Just wipe a small film of grease on the bushing before installation and you will be amazed at how much easier it will snap into the hole. To learn more about each one or to purchase individually please click on the appropriate link below:īONUS: We are sending a small packet of special silicone grease along with your new bushings at no extra charge. The Clip tool and clips are available for purchase separately as well as the bushings. You will be allowed three downloads, so please save the file on your machine for backup.

#SHIFT LINKAGE BUSHING REPLACEMENT PDF#

Any PDFs will show up under My PDF Manuals.

#SHIFT LINKAGE BUSHING REPLACEMENT DOWNLOAD#

Once you complete the purchase of this product you will be able to download the digital instructions immediately when you are logged in and on your personal account page (click on My Account). _ How to view the PDF digital instructions: They will just crumble and fall out of the holes in the metal shift levers. Here is what happens to these bushings when they get old and tired. White bushing measures: ( In the groove) 15.85 mm OD, 9.82 mm ID, width 13.8 mm 2 new nylon bushings - (comes with a pouch of synthetic grease) This complete kit includes the following: